• Home
  • About
  • Franchising
  • Gallery
  • Contact
  • Email us - info@themistingcompany.co.za
  • Droplets of water saved:

Components of a Misting System

Misting Pump - 1, 1.7 and 4.4 litres per minute

Features

Components of a Misting System - The Misting Company

Dual Bearing Design

Lowers the heat and noise by reducing friction and wear.

Forged Manifold

Anti-rust, non-leaking design extends the life of the pump.

Rinse Cooling Design

Internal rinse design channels water to packings to reduce heat stress and increase the life of the packings.

Automatic Pressure Valve

Controls the consistency of the pressure, regardless of the number of nozzles used and nozzles becoming clogged.

Circuit Breaker

Stops the motor if the voltage is outside of the safety parameters.

Misting Machine - 1.7 and 4.4 litres per minute

Features

Components of a Misting System - The Misting Company

Complete System

All-in-one design includes pump, timer, inlet filter, pressure release valve and pressure switch. No need to buy and install accessories.

Time Control

24 hour digital timer with eight setting for minutes and seconds to set exact specifications for misting.

Pressure Release

Automatically releases pressure from the mist line when the pump stops to prevent leaking nozzles.

Circuit Breaker

For electrical safety if the voltage is outside of the parameters.

Filter

The 0.1mm dual-mesh filter prevents debris from entering the pump. SST mesh for easy cleaning.

Complete Nozzle Unit

Components of a Misting System - The Misting Company
  • Brass
  • Stainless steel orifice and filter
  • Anti-drip
  • Cleanable
  • Orifice size 01.5mm, 0.2mm, 0.3mm

Brass Nozzle

Components of a Misting System - The Misting Company
  • Brass
  • Stainless steel orifice
  • Orifice size 0.3mm

Nozzle Extension

Components of a Misting System - The Misting Company
  • Brass
  • 5cm and 15cm

Inlet Filter

Components of a Misting System - The Misting Company
  • Length: 15cm
  • Mesh diameter 0.1mm
  • Working pressure 0-5kgf/cm2
  • SST mesh for easy cleaning

Low Pressure Switch

Components of a Misting System - The Misting Company
  • Voltage: 110V/220V
  • Working pressure: 7 Bar
  • Thread: PT1/4M

Solenoid Valve

Components of a Misting System - The Misting Company
  • Model: SV-01
  • Size: 1/4
  • Voltage: 220
  • Hz: 50/60
  • IIO/IIC: IIC
  • Pressure: 10kgf/cm2

Installation

Misting Fan

The cooling misting or humidification effects depend on a number of factors including, but not limited to, the size of the misting fans, nozzle sizes, spacing between nozzles and the relative humidity

Spacing

Standard spacing between the nozzles ranges from 0.5 to 1.5 meters. Standard spacing between pipelines is determined by nozzle output and the desired cooling and humidity to be created

Pumps and Nozzles

The choice of pumps and nozzles are determined by the size of the installation site, the requirements of cooling, misting and humidification effect and the humidity in the air.

Pump

The pump is determined by the number and sizes of the nozzles used. E.g. if the flow of a nozzle is 0.05 litres/min and there are 300 nozzles then the total volume required per minute is 15,15 litres / min. We would then use pumps with a minimum output volume of 15 litres/min and a pump pressure more than 70kgf/cm2 will achieve the best results.

Nozzles

For best misting effects, we choose nozzles with small orifice sizes to reinforce cooling and to avoid any leaking nozzles. It also helps to increase the negative ions in the air.